Frigidaire FFGW2426US Fiche technique Page 3

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 3
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 2
INSTALLATION SPECIFICATIONS
Product Shipping Weight (approx.) – 164 Lbs.
Voltage Rating – 120V / 60 Hz / 15 Amps
Connected Load (kW Rating) @ 120 Volts = .60 kW
(For use on adequately wired 120V, dedicated circuit having 2-wire service
with a separate ground wire. Appliance must be grounded for safe operation.)
Amps @ 120V = 5 Amps
Always consult local and national electric and gas codes.
Oven ships with 3/4" factory regulator.
LP Gas convertible.
Do not obstruct flow of combustion air at oven vent nor around base or
beneath lower front panel of appliance. Oven requires fresh air for proper
burner combustion.
Oven vent location should be a minimum 36" height above floor.
Minimum 21-1/4" clearance for oven door depth when open.
Full oven base of solid plywood or similar material required, capable of
supporting 150 Lbs.
Base must be level and cabinet front must be square.
Single Wall Oven is NOT approved to be used in side-by-side installation.
Single Wall Oven is NOT approved to be used alone in under-counter
installation or in combination with any Frigidaire® Warmer Drawer or Built-In
Microwave Oven.
ALTERNATE INSTALLATIONS
Oven can also be installed into an existing two-cavity oven cutout opening
measuring 42-1/8" H x 22-1/2" W. To accommodate opening for smaller
oven, filler strips need to be installed vertically on each side of opening along
with two standard 2 x 4s (22" minimum length), installed upright on each
side beneath oven’s side rails, flush with cabinet front. Two height adjusters,
located on bottom sides of oven wrapper, must also be lowered to raise
oven by 1". Oven’s bottom trim will then overlap cabinet face 1/4" minimum
to hide opening at bottom.
To accommodate existing 37-1/2" to 39" cutout height, oven’s height adjusters
must be lowered to raise oven by 1" in addition to bottom trim’s 1/2" overhang
allowing for a 1-1/2" total height adjustment.
Specifications subject to change. Accessories information available on the web at frigidaire.com
Note: For planning purposes only. Always consult local and national electric, gas and plumbing codes.
Refer to Product Installation Guide for detailed installation instructions on the web at frigidaire.com.
USA
10200 David Taylor Drive
Charlotte, NC 28262
1-800-FRIGIDAIRE
frigidaire.com
CANADA
5855 Terry Fox Way
Mississauga, ON L5V 3E4
1-800-265-8352
frigidaire.ca
FFGW2426U 05/18
© 2018 Electrolux Home Products, Inc.
Alternate Installation
Oven can also be installed into an existing two-cavity oven cutout
opening measuring 42
1
/8"
H x 22
1
/2"
W. To accommodate opening
for smaller oven, filler strips need to be installed vertically on each
side of opening along with two standard 2 x 4s (22" minimum length),
installed upright on each side beneath oven’s side rails, flush with
cabinet front. Two height adjusters, located on bottom sides of oven
wrapper, must also be lowered to raise oven by 1". Oven’s bottom trim
will then overlap cabinet face
1
/4" min. to hide opening at bottom.
To accommodate existing 37
1
/2" to 39" cutout height, oven’s height
adjusters can be lowered to raise oven by 1" in addition to bottom
trim’s
1
/2" overhang allowing for a 1
1
/2" total height adjustment.
24" Single Gas Wall Ovens_1-1/2 Cell
Frigidaire Baseline (models FFGW2415Q & FFGW2425Q)
24"
min.
1
1
/2"
min.
10
"
min.
27
1
/2"
max.
37
1
/2"
min.
38"
max.
22"
24"
min.
10"
min.
27
1
/2"
max.
2"min.
20"
1
1
/2" Dia.
hole for gas
hookup
7
5
/8"
C
L
Electrical
outlet
location
Full base
required to
support
150 lbs.
Bottom cutout
edge must be
finish cut
Hole for
electrical
cord
Height
adjuster
37
3
/8"
21
11
/
16
"
25
3
/8"
23
3
/8"
Power
supply
location
(left
bottom
rear)
38
7
/16"
23
7
/8"
Allow at
least 21
1
/4"
clearance for door
depth when open
FFGW2426U S/W/B
SINGLE WALL OVEN
24" GAS
Vue de la page 2
1 2 3

Commentaires sur ces manuels

Pas de commentaire