Frigidaire FFID2426TS Manuel d'utilisation et d'entretien Page 5

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 16
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 4
5
OPERATING INSTRUCTIONS
Sanitize Option
To sanitize your dishes and glassware, select
SANITIZE option. When selected, the light
above the pad will come on and remain on until
end of cycle. The water temperature in the
nal rinse will be raised to 155
o
F (68
o
C) and will
maintain that temperature for 9 minutes. This
option is available in Heavy and Normal Cycles.
Only these sanitization cycles have been
designed to meet NSF requirements.
The cycle time will be extended until the proper
water temperature is reached.
Washing
action will continue during the water heating
delay. For best results, the incoming water
temperature should be at least 120
o
F (49
o
C).
The sanitize criteria may not be satisfi ed if there
is an interruption of the cycle, power failure or if
the incoming water temperature is below 120
o
F
(49
o
C).
To turn off the SANITIZE option, press the pad
a second time. The light above the pad will
turn off.
Delay Start
The DELAY START option allows you to
automatically delay starting your dishwasher
from 2-4-6 hours.
To activate delay start option, press the pad
once for a 2 hour delay, twice for 4 hours and
three times for 6 hours. A light will come on
indicating the delay start hours and will remain
on until cycle starts.
Press the START/CANCEL pad to start the delay
option. If the delay option is interrupted, the
START/CANCEL pad will have to be pressed
again to return to delay option.
To cancel the DELAY START option and to
begin the selected cycle before the delay
period is over, press and hold START/CANCEL
pad for 3 seconds.
When AIR DRY is selected the heater will be
de-activated during the drying phase of the
selected wash cycle. This will slightly lower
the energy use but will increase the likelihood
that the dishware will not dry completely. If
AIR DRY is not selected the heater will be
activated during the drying phase of the
selected wash cycle.
Child Lock Controls
To prevent children from accidently changing
the dishwasher cycle or starting the
dishwasher, lock the dishwasher controls
by pressing and releasing the AIR DRY pad
for 3 seconds while the door is open. An
indicator light on the lock graphic pad will
illuminate when the controls are locked and no
new selections can be made until the lock is
released. To unlock the controls, press the AIR
DRY pad until the indicator light goes out.
To Cancel a Cycle
You can cancel a cycle anytime during the
cycle. Press and hold the START/CANCEL pad
for 3 seconds. The light above the cycle and
option selected will go out, and the START/
CANCEL light will remain illuminated, the
dishwasher will start a 90 second drain. At the
end of the drain, select the next desired cycle.
Status Indicator Lights
The WASHING light comes on at the beginning
of the cycle and remains on until the end of
the main wash.
Whether heated or unheated dry is selected
the DRYING light will come on during the
drying portion of the cycle.
When the SANITIZE option is selected, the
SANITIZED light will glow when the SANITIZE
cycle is fi nished. If the dishwasher did not
properly sanitize the dishes, the light will not
come on. This can happen if the cycle is
interrupted. The light will remain on until the
door is opened.
The CLEAN light will come on at the end of
cycle and remain on until the door is opened.
The DishSense
TM
Technology checks the soil
level on your dishes in the HEAVY WASH,
NORMAL WASH and TOP RACK cycles.
Depending on soil level, the sensor will
determine if additional water fi lls are needed
to clean the dishes or if water fi lls can be
deleted. Cycle time and water usage will
vary based on the amount of soil on the
dishes. Cycle time will also vary based on
the options selected and the incoming water
temperature.
Air Dry
Vue de la page 4
1 2 3 4 5 6 7 8 9 10 ... 15 16

Commentaires sur ces manuels

Pas de commentaire