FIG.18
6
Installation Instructions
Slide inner window sash firmly against side of the cabinet. Make sure not to peel the seal strips from the window
track and cabinet side channels. If the panel frame does not fit snugly to the inner window sash, secure the panel frame
to the sash with #8 x 3/4″ self-threading screws. Use the partially plugged holes in the panel frame. Drill 1/8″ pilot
holes for the screws.
Hook the safety bracket over the base of the unit and fasten it to the front of the platform assembly (FIG.18). Use
a #8-32 x 3/4″ self-threading screw.
NOTE: The bracket prevents movement of the air conditioner (either in or out) after completing the installation.
Stuff the window sash seal between the vertical sash and the window glass, as shown (FIG.19).
Use the window locking bracket to lock the inner window sash to the base of the outer window sash (FIG.19).
Use one #8 x 3/4″ screw, or #8-32 x 3/4″ self-threading screw. (Drill 1/8″ pilot hole).
To replace the front first reconnect the coupler plugs, make the exhaust control positioned through the front in
the proper location. Gently push the front into position on the cabinet. It should click into place. Then replace the
retaining screws that holds the panel in place. DO NOT push or pull the front panel louvers.
Insttall safety bracket
window sash seal
Window
locking
bracket
To install in windows having no flanges or wood stops on the top and side jambs, the channels and panel frame must
fit against a matching flange (or 1/16″ max. thick angle) attached to the window jambs. FIG.20A shows this angle
installed. FIG.20B & FIG.20C show alternate treatments. On the sash side of the opening, the leading corner of the inner
sash becomes the flange. You can purchase the angle strip locally.
Alternate Window Jamb Applications
FIG.20C
FIG.20A
FIG.20B
Add angle to wood stop Add wood as shown
Add 16- or 18- gage angle
Room
3/4” or 1”
Room
1”x1“ or
3/4”x3/4”
angle
Installing the Unit in a Casement Window
NOTE:
Open the window the maximum amount to allow for clearance of the cabinet.
The crank handle should be removed to allow the platform to be fastened to
the jamb. If the window cannot open far enough (more than 15-1/2″) for the
cabinet to clear the window, remove the window entirely by drilling out the
rivets. Bolts can serve as the pivots in the feature.
To avoid crank handle and window clearance problems, the unit can be
installed in a stationary sash section. However, the horizontal mullion and
the 2 glass panels must be removed before installation.
Attach support brace to platform as shown (FIG.21). Use the adjustment bolt
and hex flange nut to complete the assembly. Choose the slot and adjustment bolt
hole location that will create a 45 degree angle between the platform and support
brace. Try the assembly in the window to determine if the platform will rest properly,
and allow the proper slope (3/16″ lower on outside).
FIG.19
Room
3/4” or 1”
Flush
Platform Assembly
1/4” (6mm) HEX
FLANGE NUT
FIG.21
19
20
21
22
23
24
safety bracket
(choose the correct
safety bracket
according to your
window type)
For Vinyl-Clad windows, use Item 20 (refer to page 3) to fasten the unit to the platform.
(2 pages)
(8 pages)
(32 pages)
(138 pages)
(8 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels